Description
FeedSavr Complete Bird Feeder Pole!
Squirrel, Deer, and many other critters are no match for our innovative critter proofing complete system!
Feed birds of all kinds with ease. Lower up to three feeders to fill, clean, or replace without getting a ladder out or using long hooks.
Save money by keeping squirrels out of your feeders, and other critters too.
Handicap accessible pulley system.
Use to hang bird feeders, bird houses, hanging plant baskets, lanterns and much more!
Keep Squirrels and Deer out of and away from your bird feeders and bird seed with our unique squirrel proof bird feeder pole. The FeedSavr bird feeder pole is squirrel proof and deer proof and easily keeps squirrels and deer away from your bird feeders at the same time leaving your feeders easily accessible for filling and cleaning.
The FeedSavr comes in 3 sturdy, light weight, aluminum sections. It has a rope and pully system, a carriage, three feeder support rods a PVC ground sleeve (for mounting the pole in your yard) and assembly instructions. Total assembly is less than 10 minutes.
Each of the three 1/4" steel arms are capable of supporting filled feeders weighing in excess of 6 lbs. Rope and pulley allows consumer to easily raise feeders to the top of pole and lower them for refilling up to 3 feeders.
In the Box
Weight - 11lbs
Dimensions - 4in x 11in x 56in
1 - Squirrel Deflector - (2 Half Circle Galvanized Plates)
1 - Squirrel Deflector Tripod
1 - Pulley Assembly
1 - Rope Cleat
1 - Rope 15 ft
3 - 3/8" Black Threaded Hangers
3 - Sections Aluminum Pole
1 - 15 inch PVC ground sleeve
Assembled - The FeedSavr Complete Critter Proof Bird Feeding Pole will stand approximately 10.5 feet above ground. The squirrel proofing deflector should be at least 48" above ground.
Bird feeders sold separately
In Use Dimensions: 24" x 24' x 144", Weight: 11 lb
Note: Ships dimensionally oversized. Additional freight may be required depending on order size and destination zone.
Recommendations:
* We recommend using only 1 bird feeder per hanger, the FeedSavr works at its best using 3 bird feeders.
* Weight capacity of each hanger is approximately 8 lbs. Feeders that are too heavy can cause damage to your FeedSavr.
* Placement of your FeedSavr is critical. For your Feedsavr to be critter resistant, place in yard away from houses, outbuildings and
trees.
Assembly Instructions:
1. Dig foundation hole approximately 3 times the diameter of the ground sleeve. Recommended dimensions are 6 inches in diameter by 18 inches deep. If using cement to secure ground sleeve, dig hole five times the diameter of the ground sleeve recommended 10 inches in diameter.
2. Plumb ground sleeve and secure so that it will not move when dirt (or cement) is filled in around the sleeve. Keep inside of sleeve free from dirt or cement.
3. Use bottom section of the pole and a level to check for straightness. Pack dirt in around ground sleeve.
4. Assemble FeedSavr hangers. Screw the 3 black feeder hangers into the threaded holes in the black hanger sleeve (Do Not Over Tighten) hooks pointing up.
5. Slide the Tripod on to the bottom pole section with the ends of the three L shaped pins facing up (do not tighten wing nut). Take both halves of the metal squirrel guard (deflector) in your hands. Slide the two halves of the deflector plates together (one folded lip into the other) to make a complete circle. Place the hole in the deflector plate over the bottom section of pole above the tripod.
6. Line up rope cleat with holes in middle section aluminum pole. Insert screws and tighten with a screw driver until just snug. (Do Not Over Tighten). When the pole is completely assembled the cleat will be closest to the upper pole section.
7. Slide the hanger sleeve assembly on the middle section of pole, above the rope cleat, with slotted rope hood open side down.
8. Tie a knot on one end of the rope, feed the other end of the rope through the pulley and tie a knot in that end of the rope. Hold both ends of the rope in one hand. Slide the end of the rope from the side of the pulley that will be closest to the pole through the rope hood on the side of the hanger sleeve and pull on the rope until the knot slides under the hood.
9. Place the middle section of the pole on to the bottom pole section. Place the pulley assembly on the female end of the top pole section and tighten set screw.
10. Line the slotted hood on the hanger assembly up with the wheel on the pulley assembly.
11. Secure the Tripod just below the cleat with the bolt and wing nut provided.